OPERATION AND PROGRAMMING


STHFVO1

Comfort Roof Control Module for

  • Volvo C70

    v1.0


  • Further information and manuals for all products can be found on our web site

    w w w . m o d s 4 c a r s . c o m

     
    We explicitly point out that all functions of this control unit should be used only while exercising caution and responsibility. We can NOT be held liable for any damage or injury caused by installing or using this product.
    PLEASE READ THE COMPLETE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
    Important Information. READ BEFORE USING!
    PRINTING THIS MANUAL
    This manual is designed to produce completely filled pages. In order to get best print results, simply set the borders to minimum settings in the browser's page setup menu and disable headers and footers.

    Activate the print preview and if necessary decrease the zoom level until all pages are shown correctly.

    ALL IMAGES CAN BE CLICKED FOR FULL SIZE in the browser.
    TROUBLE SHOOTING - NEED TO CONTACT US?
    If you run into any problems after installing the module, please go over the manual again in great detail, clicking every photo for full size!
    We now have a full Knowledge Base with Support Ticket system available online at www.mods4cars.com/support

    If you need to contact us, the best and fastest way to do so is by opening a support ticket there

    This module comes with our USB Field Upgrade and Configuration Port! We recommend connecting it to a computer BEFORE YOU INSTALL and using our support app "m4cconnect" to do a quick firmware update check. M4cconnect as well as all other information regarding USB update and configuration can be found at www.mods4cars.com/usb. You can even configure and activate your favorite module functions and settings on screen before the module is installed in the car! It is a good idea to permanently install the USB cable with the module in the car, leaving the computer plug in an easily accessible spot for later use with a Wifi/3G/4G connected laptop.
    Detailed function description (* = Factory setting)
    Function 1 - Main Switch - Workshop and Diagnostics ( 0=OFF / *1=ON / 2=NO HAZARDS )
    The module can quickly and easily be enabled and disabled using this function. It acts like a master switch. When disabled, the module becomes completely inactive and behaves as if it was not installed.
    Setting 0 disables the entire module while keeping all other function settings intact. This allows turning the module off and back on without the need to reconfigure all of the other user configurable settings.
    Setting 2 disables blinking of the hazards (only in the side mirrors) during remote operation.

    IMPORTANT: In order to avoid problems with diagnostic tools and to avoid confusion or injury by unexpected top movement, we urge you to ALWAYS DISABLE the module before taking the car to a shop or lending it to a third person! If problems with the top arise while the module is installed, ALWAYS contact Mods4Cars first at www.mods4cars.com. NEVER take the car to a dealer without getting support first!


    Function 2 - One-Touch for the soft-top switch ( 0=OFF / *1=ON / 2=EXTENDED[!] )
    When enabled, the center console switch operation is enhanced as follows:

    • Holding down the switch in either direction will operate the top as long as the switch is held.

    • A short tap on "OPEN" will open the top completely.

    • A short tap on "CLOSE" will close the top completely.
    • Tap in the opposite direction at any time for emergency stop.

    When set to EXTENDED mode, it is possible to turn the ignition off and pull the key out, while the top operation continues.
    Please use with extra caution to avoid injury by moving top parts!


    Function 3 - Remote Control ( 0=OFF / *1=ON / 2=EXTENDED[!] )
    This function allows top operation with the original remote fob by tapping the "OPEN" or "CLOSE" button on the remote. Once started, the top will complete the cycle automatically. Tapping any button on the remote will interrupt the operation immediately.
    While the top in in motion, the hazard lights flash as a warning signal (unless disabled by function 1).

    Full overview of all modes of remote operation:
    • Hold down UNLOCK on the remote to open all windows (factory feature).
    • Tap LOCK on the remote twice to close all windows.
    • Tap UNLOCK on the remote 3x (in 1 sec intervals) to open the top.
    • Tap LOCK on the remote 3x (in 1 sec intervals) to close the top.
    • Alternatively tap UNLOCK 3x (when fully open) to close the top if using the LOCK button triggers the alarm. With extended mode active it is possible to lock the car while the top is closing.

    When set to EXTENDED mode, it is possible to turn the ignition on and start the engine or lock the doors with the remote, while the top operation continues.
    Please use with extra caution to avoid injury by moving top parts!


    Function 4 - Maximum allowed speed for top operation ( *0=0kmh / 1=10kmh / 2=20kmh / 3=30kmh / 4=40kmh )
    Setting the max allowed speed for top operation in steps of 10km/h (~7mph). Setting 0 only allows roof operation while halted.
    WARNING: Once the top is started within the programmed speed limit, it will continue running, even if the speed later exceeds the limit during the top operation!


    Function 5 - All-Windows-Switch ( *0=NORMAL / 1=ONE-TOUCH )
    This function allows to program the driver's door "all-windows" switch to raise all windows using One-Touch. By factory this switch only does One-Touch down.


    Function 6 - Automatic door unlocking ( *0=OFF / 1=ACC / 2=IGN )
    This function can be set to automatically unlock the doors when either the key is pulled from the ignition lock (setting ACC) or when the ignition is turned off (setting IGN). This removes the requirement to pull the door handles twice to get out of the car.


    Function 7 - Passenger mirror park assist ( *0=OFF / 1=ON )
    Requires Seat memory. When enabled, the passenger side mirror will dip down upon shifting to reverse gear. After leaving reverse gear, the mirror will return back up if one of these conditions is met: a) 10 sec. inactivity or b) forward speed of >5mph is detected.
    The module switches between memory positions 1 (driving) and 3 (backing up), so to program the desired backing up mirror position, simply save its position in memory no. 3.
    Programming
    This module is equipped with our interactive setup feature to allow easy setting of the desired options.
    All programming is done by using the rooftop switch (4) and the two green turn signal (indicator) arrows (2 and 3). Functions are indicated by the left arrow (2) and their settings are indicated by the right arrow (3). Navigation is done by pushing the top close button (next function) or the top open button (next setting). After selecting the last function or function setting, the setup automatically jumps back to the first function / lowest setting. Each time either a new function is selected or a function's setting is changed, the arrows will indicate the new status by first blinking the function (left arrow) and then the current setting (right arrow).
    To enter programming mode: Turn the ignition fully ON, then push and hold the driver's door unlock switch (1) until the left arrow blinks once to indicate function 1. Now let go of the switch. From this point on you can navigate through the functions by pushing the top close button and once the arrows are finished indicating the function and setting, change the setting by pushing top open. The new settings are active immediately.

    To end programming mode, either wait for 30 sec. or push the unlock switch again. End of programming mode is indicated by both arrows lighting up simultaneously for 1 second.



    Function/Setting Matrix (*green fields are defaults)
    Product: STHFVO1 - SmartTOP for Volvo C70
    Firmware: v1.xx
    SETTING 0SETTING 1SETTING 2SETTING 3SETTING 4
    FUNCTION 1 OFF*ONNOHAZ--
    Main SwitchModule DisabledModule EnabledModule Enabled + Hazard Blinkers off
    FUNCTION 2 OFF*ONETOUCHEXTENDED--
    Conv. Top One-TouchDon't change center console switch behaviorEnable one-touch operation while drivingAllow ignition off during top operation
    FUNCTION 3 OFF*ONEXTENDED--
    Remote ControlNo remote functionsEnable remote functionsAllow ignition on during top operation
    FUNCTION 4 *0 km/h10 km/h20 km/h30 km/h40 km/h
    Maximum SpeedOnly while halted10 km/h (~7mph)20 km/h (~13mph)30 km/h (~19mph)40 km/h (~25mph)
    FUNCTION 5 *OFFONETOUCH---
    All WindowsFactory behaviorOne-Touch operation to raise all windows
    FUNCTION 6 *OFFKEYIGN--
    Automatic Door UnlockingDisabledUnlock doors when key is pulledUnlock doors when ignition is turned off
    FUNCTION 7 *OFFON---
    Park assist (pass.mirror)Park Assist feature disabledPassenger Mirror Park Assist enabled