INSTALLATION X5 (E70)


TVLBBW1

Universal TV/DVD in motion enabler for

  • BMW 1 - E8x
  • BMW 3 - E9x
  • BMW 5 - E60/E61
  • BMW 6 - E63/E64
  • BMW 7 - E65/E66
  • BMW X5 - E70
  • BMW Z4 - E89

    v1.xx (All Versions)


  • Further information and manuals for all products can be found on our web site

    w w w . m o d s 4 c a r s . c o m

     
    We explicitly point out that all functions of this control unit should be used only while exercising caution and responsibility. We can NOT be held liable for any damage or injury caused by installing or using this product.
    PLEASE READ THE COMPLETE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
    Important Information. READ BEFORE INSTALLING!
    PRINTING THIS MANUAL
    This manual is designed to produce completely filled pages. In order to get best print results, simply set the borders to minimum settings in the browser's page setup menu and disable headers and footers.

    Activate the print preview and if necessary decrease the zoom level until all pages are shown correctly.

    ALL IMAGES CAN BE CLICKED FOR FULL SIZE in the browser.
    TROUBLE SHOOTING - NEED TO CONTACT US?
    If you run into any problems after installing the module, please go over the manual again in great detail, clicking every photo for full size!
    We now have a full Knowledge Base with Support Ticket system available online at www.mods4cars.com/support

    If you need to contact us, the best and fastest way to do so is by opening a support ticket there

    This module comes with our USB Field Upgrade and Configuration Port! We recommend connecting it to a computer BEFORE YOU INSTALL and using our support app "m4cconnect" to do a quick firmware update check. M4cconnect as well as all other information regarding USB update and configuration can be found at www.mods4cars.com/usb. You can even configure and activate your favorite module functions and settings on screen before the module is installed in the car! It is a good idea to permanently install the USB cable with the module in the car, leaving the computer plug in an easily accessible spot for later use with a Wifi/3G/4G connected laptop.
    IMPORTANT TROUBLESHOOTING TIPS

    If the top does not work properly or at all after installing the module, these tips can be very helpful:

    • 1) Turn Function 1 (Main Switch) off (Setting 0). The module will be completely passive. If the problem still persists and the top won't work, check all connections. Please also check the green DATA LED on the module!

    • 2) Function 2 now has a valet mode (Setting 2) on many modules. Valet mode completely disables opening of the top. Check the setting for function 2 and make sure the module is NOT in valet mode!

    IMPORTANT: Not all modules have the valet mode! Please check the Operation and Programming Manual!
    The green InstallAID™ LED signals a correct installation and shows the status of the module. On new modules this LED is labeled with DATA.

    LED OFF
  • Ignition OFF: CAN bus and module are in low-power standby mode. This is normal.
  • Ignition ON: Either power connection or CAN bus connection is interrupted. Check the two wire taps for power and ground as well as the CAN connectors. Also make sure the CAN polarity is correct.
    LED either dimly lit or flickering erratically
  • A dim or flickering LED is an indicator for interrupted or missing POWER or GROUND connections. The module will get some leakage current from the CAN bus which causes the LED to stay dimly lit or flicker erratically. See previous paragraph about wire taps if applicable!
    LED permanently ON
  • Module is connected to CAN and power, but does not receive the correct data. Recheck all connections thoroughly. A VERY COMMON source of problems is reversed polarity on the CAN wires. Double-check the POLARITY and wire-colors of all connections!
    LED blinks
  • CAN bus is active, the module is connected correctly and ready for use.
  • USE OF THE 3M WIRE TAPS
    This module is installed using the 3M wire taps very popular with 12V aftermarket industry for their reliability and durability. The most common problem during installation is a bad contact between the plugs from the supply wires and the wire taps. Please make absolutely sure that the metal blades of the plugs slide into the slots of the t-taps. It happens that the blade "misses" the slot and the connection looks correct, but doesn't make electrical contact!

    The T-taps come in RED (for thin wires), BLUE (for medium wires) and YELLOW (for thick wires).

    To test if you installed the module correctly after all wires are connected, turn the ignition fully on and watch the green LED on the module. It should blink (flash) to signal a correct installation. If the LED either does not turn on or stays on permanently, there is a bad contact or a missing connection! See detailed explanation of the DATA LED.
    Installation - Steps 1-3
    1. Before starting with the installation, turn the ignition fully off and pull the key! Remove the center vent by pulling it out starting from the bottom. It is snapped in place.
    2. Remove all connectors on the back and put the vent piece aside.
    3. Remove the two screws (1) and (2) of the fascia plate.
    Installation - Steps 4-6
    4. Remove entire fascia plate by starting from the bottom with a soft plastic tool or putty knife as a lever. It is snapped in place around the bottom.
    5. Remove the A/C control panel and unplug all connectors on the back. Put it aside.
    6. Remove all four screws (1) through (4) on the CPU unit. Then pull entire unit straigt out. It is guided by rails on the sides and can be wiggled out with gentle up/down and sideways movements.
    Installation - Steps 7-9
    7. Carefully unplug all connectors on the back. Use a screw driver for the locking latches on the big black square plug. Put the CPU unit aside.
    8. Remove the cloth tape around the wiring harness tubing, then move the tubing back to gain access to the individual wires.
    9. Identify the correct wires as shown: The thick brown wire is for GROUND and the thick red/green wire is for +12V power. The twisted orange/green wire pair is the CAN data bus. IMPORTANT: In case there are several orange/green pairs, make sure you use the one that has its green wire going into the fron slot (1) on the big black plug.
    Installation - Steps 10-11
    10. Attach the supplied wire taps with combination pliers. One to the red/green wire (1) and one to the brown wire (2). Cut the CAN bus wires (3) and connect the module wiring harness in the next step. IMPORTANT: Use combination pliers for the round red splices and make sure that the wire ends are fully inserted to avoid bad or intermittent electrical contact.
    11. Click the picture for detailed view! The wire pairs on the module wiring harness are labeled 'IN' and 'OUT'. Connect the IN wire pair from the module to the car side (orange with orange/green in one splice and brown with green in the other), then connect the OUT pair to the monitor plug (orange with orange/green in one splice and brown with green in the other). Connect everything exactly as shown, then attach the plug to the CPU unit and briefly press the unlock button on the remote to wake up the CAN data bus. A blinking green LED on the module signals a correct install. Put everything back together in reverse order.