INSTALLATION 6 Series (E63/E64)


TVLBBW1

Universal TV/DVD in motion enabler for

  • BMW 1 - E8x
  • BMW 3 - E9x
  • BMW 5 - E60/E61
  • BMW 6 - E63/E64
  • BMW 7 - E65/E66
  • BMW X5 - E70
  • BMW Z4 - E89

    v1.xx (All Versions)


    • Further information and manuals for all products can be found on our web site

    w w w . m o d s 4 c a r s . c o m

     
    We explicitly point out that all functions of this control unit should be used only while exercising caution and responsibility. We can NOT be held liable for any damage or injury caused by installing or using this product.
    PLEASE READ THE COMPLETE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
    Important Information. READ BEFORE INSTALLING!
    PRINTING THIS MANUAL
    This manual is designed to produce completely filled pages. In order to get best print results, simply set the borders to minimum settings in the browser's page setup menu and disable headers and footers.

    Activate the print preview and if necessary decrease the zoom level until all pages are shown correctly.

    ALL IMAGES CAN BE CLICKED FOR FULL SIZE in the browser.
    TROUBLE SHOOTING - NEED TO CONTACT US?
    If you run into any problems after installing the module, please go over the manual again in great detail, clicking every photo for full size!
    We now have a full Knowledge Base with Support Ticket system available online at www.mods4cars.com/support

    If you need to contact us, the best and fastest way to do so is by opening a support ticket there

    This module comes with our USB Field Upgrade and Configuration Port! We recommend connecting it to a computer BEFORE YOU INSTALL and using our support app "m4cconnect" to do a quick firmware update check. M4cconnect as well as all other information regarding USB update and configuration can be found at www.mods4cars.com/usb. You can even configure and activate your favorite module functions and settings on screen before the module is installed in the car! It is a good idea to permanently install the USB cable with the module in the car, leaving the computer plug in an easily accessible spot for later use with a Wifi/3G/4G connected laptop.
    IMPORTANT TROUBLESHOOTING TIPS

    If the top does not work properly or at all after installing the module, these tips can be very helpful:

    • 1) Turn Function 1 (Main Switch) off (Setting 0). The module will be completely passive. If the problem still persists and the top won't work, check all connections. Please also check the green DATA LED on the module!

    • 2) Function 2 now has a valet mode (Setting 2) on many modules. Valet mode completely disables opening of the top. Check the setting for function 2 and make sure the module is NOT in valet mode!

    IMPORTANT: Not all modules have the valet mode! Please check the Operation and Programming Manual!
    The green InstallAID™ LED signals a correct installation and shows the status of the module. On new modules this LED is labeled with DATA.

    LED OFF
  • Ignition OFF: CAN bus and module are in low-power standby mode. This is normal.
  • Ignition ON: Either power connection or CAN bus connection is interrupted. Check the two wire taps for power and ground as well as the CAN connectors. Also make sure the CAN polarity is correct.
    LED either dimly lit or flickering erratically
  • A dim or flickering LED is an indicator for interrupted or missing POWER or GROUND connections. The module will get some leakage current from the CAN bus which causes the LED to stay dimly lit or flicker erratically. See previous paragraph about wire taps if applicable!
    LED permanently ON
  • Module is connected to CAN and power, but does not receive the correct data. Recheck all connections thoroughly. A VERY COMMON source of problems is reversed polarity on the CAN wires. Double-check the POLARITY and wire-colors of all connections!
    LED blinks
  • CAN bus is active, the module is connected correctly and ready for use.
    • USE OF THE 3M WIRE TAPS
    This module is installed using the 3M wire taps very popular with 12V aftermarket industry for their reliability and durability. The most common problem during installation is a bad contact between the plugs from the supply wires and the wire taps. Please make absolutely sure that the metal blades of the plugs slide into the slots of the t-taps. It happens that the blade "misses" the slot and the connection looks correct, but doesn't make electrical contact!

    The T-taps come in RED (for thin wires), BLUE (for medium wires) and YELLOW (for thick wires).

    To test if you installed the module correctly after all wires are connected, turn the ignition fully on and watch the green LED on the module. It should blink (flash) to signal a correct installation. If the LED either does not turn on or stays on permanently, there is a bad contact or a missing connection! See detailed explanation of the DATA LED.
    Installation - Steps 1-3
    1. IMPORTANT: Turn ignition off and pull key before installing! The switch unit with hazard and door button must be removed first to gain access to a screw underneath.
    2. Use a plastic tool to pry it out from below. It is just snapped in place with two metal springs. Pull whole unit out.
    Click Play on the left for a video demonstration.
    3. Disconnect the plug on the back.
    Installation - Steps 4-6
    4. Now remove the torx screw underneath which is holding the air vent unit in place.
    5. With the screw gone, pry out the air vent unit. It is latched into place with metal springs.
    6. Disconnect all plugs on the back and set vent unit aside.
    Installation - Steps 7-9
    7. Remove the two philips head screws (1) and (2) on the sides, then pull fascia toward you.
    8. Use a plastic tool to pry it out on the bottom. There are several spring latches around and on the bottom.
    9. Remove four torx screws on the radio unit. Put gear shifter in D gear (pull handbrake) otherwise it will be in the way. Pull out the entire radio unit.
    Installation - Steps 10-12
    10. Disconnect the large connector on the back by flipping the locking lever over and pulling.
    11. Remove most of the fabric tape around the wires.
    12. Attach the supplied wire taps to the thick brown (ground) and the thick red (+12V) wires.
    Installation - Steps 13-15
    13. Cut the twisted black and yellow wire pair. This is the CAN Bus where the smartTV module needs to go in between.
    14. Using the supplied crimp connectors, connect the black wire from the radio plug with the orange wire to the module (second contact from top right) and the yellow wire from the radio plug with the brown wire to the module (second contact from bottom right). Then connect black from vehicle harness with orange to module (middle of plug) and yellow from vehicle harness with brown to module (middle of plug). See picture in step 15 for connection details.
    15. Connect power, then attach smartTV module to harness and reconnect the radio plug to the back of the radio. Tap the unlock button on the remote and watch the green LED on the module which will indicate a successful installation with a bright steady blinking pattern. Now stow the module in the void behind the radio and re-assemble everything in reverse order.